MT-3109 AC/DC Digital Clamp Multimeter User’s Manual 1st Edition, 2011 ©2011 Copy Right by Prokit’s Industries Co., Ltd.
MT /DC Digital Clamp Multimeter -3109 AC Warning To avoid damages to the Meter or to the devices under test, disconnect circuit power and discharge a
MT-3109 AC/DC Digital Clamp Multimeter voltage drop across the junction. A good silicon junction drops between 0.5V and 0.8V. To test the diode out
MT-3109 AC/DC Digital Clamp Multimeter 3. The buzzer may or may not sounds if the resistance of a circuit under test is between 50Ω to 100Ω 4. The b
MT-3109 AC/DC Digital Clamp Multimeter F. Duty Cycle Measurement (see figure 8) F. Duty Cycle Measurement (see figure 8) Warning To avoid harms t
MT-3109 AC/DC Digital Clamp Multimeter 13 3. Press the lever to open the transformer jaw. 4. Center the conductor within the transformer jaw, then rel
MT-3109 AC/DC Digital Clamp Multimeter H. Capacitance measurement (see figure 10) figure 10 Warming To avoid damage to the Meter or to the equipment
MT-3109 AC/DC Digital Clamp Multimeter Specifications A. General Specifications: Maximum Voltage between any Terminals and grounding: Refer to di
MT-3109 AC/DC Digital Clamp Multimeter 16 Accurate Specifications Accuracy: +(a% reading + b digits). Operating temperature: 23℃±5℃ Relative humidity:
MT-3109 AC/DC Digital Clamp Multimeter C. Resistance Range Resolution AccuracyOverload protection 400.0Ω 100mΩ +(1.2%+5)4.000kΩ 1Ω 40.00kΩ 10Ω 400.0kΩ
MT-3109 AC/DC Digital Clamp Multimeter F. Frequency Range Resolution Accuracy Overload protection 10Hz 0.00Hz 100Hz 0.01Hz 1kHz 0.1Hz 10kHz 1Hz 100kH
MT-3109 AC/DC Digital Clamp Multimeter Overview This Operating Manual covers information on safety and cautions. Please read the relevant information
MT-3109 AC/DC Digital Clamp Multimeter Hold the Meter tight and press the lever to open the transformer jaw. Center the conductor within the transf
MT-3109 AC/DC Digital Clamp Multimeter ●Change to AC: Change to AC by using average response method. Input sine wave, then adjust the reading until it
MT /DC Digital Clamp Multimeter -3109 ACB. Replacing the Battery (see figure 11) Warning To avoid false readings, which could lead to possible elec
MT-3109 AC/DC Digital Clamp Multimeter 22 MT-3109 數位交直流鉗表 中文說明書 一、概述 MT-3109 是一種性能穩定、安全、可靠的 3 3/4 位交直流數字鉗形表(以下簡稱鉗表)系列。整機電路設計以大規模積體電路雙積分 A/D 轉換器為核
MT-3109 AC/DC Digital Clamp Multimeter 三、安全操作準則 請注意“警告標識△及警告字句"。警告表示對使用者構成危險、對儀表或被測設備可能造成損壞的情況或行動。 本儀表嚴格遵循 GB4793 電子測量儀器安全要求以及 IEC61010-1和 IECI010-2-0
MT-3109 AC/DC Digital Clamp Multimeter 四、電氣符號︰ 雙重絕緣 AC(交流) 二極體 接地 DC(直流) 表內電池不足 警告提示 蜂鳴通斷 AC 或 DC(交流或直流) 高壓符號 中國技術監督局 製造計量器具許可證 符合歐洲共同體(E
MT-3109 AC/DC Digital Clamp Multimeter 六、顯示符號(見圖 2) 25 1. 交流信號測量指示 2. 直流信號測量指示 3. 電池電量不足指示 4. 自動量程指示 5. 二極體測試指示 6. 連續檢測指示 7. 占空比測量指示
MT-3109 C/DC Digital Clamp Multimeter A 4. 自動關機︰在測量過程中,功能按鍵和轉盤開關在 1 5 分鐘內均無動作時,鉗表會“自動關機"(休眠狀態),以節約電能; 要取消自動關機功能,只要按著 SELECT 鍵開機,則自動關機功能被取消。自動關機狀態下,按
MT-3109 AC/DC Digital Clamp Mu ter ltime2.交流電壓測量(V )(見圖 4) 27 △警告 鉗表不得用於電壓大於 600V 交流/直流導電的物體上 ﹡設置轉盤 將功能轉盤置於“"測量檔。 ﹡選擇功能 按 SELECT 鍵選擇為交流電壓測量,最初設置 為
MT-3109 AC/DC Digital Clamp Multimeter 較好的結果。 在完成所有的測量操作後,要斷開表棒與被測電路的連接,並從輸入端拿掉表棒。 △警告:在連接負載以前務必將電路電源切斷 ﹡設置轉盤到位置 ﹡選擇功能 按 SLLECT 鍵選擇二極體測 ﹡連接負載 若將元件從電路中
MT-3109 AC/DC Digital Clamp Multimeter Use the Meter only as specified in this operating manual, otherwise the protection provided by the Meter may be
MT-3109 AC/DC Digital Clamp Multimeter 7.占空比測量( Duty%)(見圖 9) △警告 圖9 鉗表不得用於電壓大於 600V 交流/直流導電的物體上 ﹡設定轉盤 將功能轉盤置於`Hz"測量檔。 ﹡選擇功能 按 REI△鍵可設定為 Duty%占空比測最。 ﹡連
MT-3109 AC/DC Digital Clamp Multimeter 對熱、機械應力均有不同程度的敏感,撞擊會短時間引起讀數變化。按住板機打開鉗頭,將鉗頭夾取待測導體,然後緩慢地放開板機,直到鉗頭完全閉合,請確定待測導體是否被夾取在鉗頭的中央,未置於鉗頭中心位置會產生附加誤差,鉗表一次只能測
MT-3109 AC/D ltimeter C Digital Clamp Mu2.環境限制 室內使用 安規︰ICE 1010-1 CAT. II600V 操作溫濕度︰0℃到 30℃(不大於 80%R.H) 30℃到 40℃(不大於 75%R.II.) 40℃到 50℃(不大於 4
MT-3109 AC/DC Digital Clamp Multimeter (3)電阻(Ω) 量 程 分辨率 準確度 過載保護 400.0 Ω 100 mΩ ±(1.2%+5)4.000 KΩ 1Ω 40.00 KΩ 10Ω 400 KΩ 100Ω ±(1%+5) 4.0
MT-3109 AC/DC Digital Clamp Multimeter (7)占空比(Duty%) 量程 分辨力 準確度 過載保護0. 1%-99. 9% 0. 1% (讀數僅供參考) 600Vp (8)直流电流() 量程 分辨力 準確度 過載保護 40. 00A 0.0
MT-3109 AC/DC Digital Clamp Multimeter AC 轉換類型︰ AC 轉換是用平均值附應模式,以正弦波輸入、校正讀數至與有效值一致。 (10)電容值() 量程 分辨力 準確度 過載保護40nF 10pF Measure at REL mode ±(5%+1
MT-3109 AC/DC Digital Clamp Multimeter 35 ©2011 Prokit’s Industries Co., LTD. All rights reserved 2011001(T)
MT-3109 AC/DC Digital Clamp Multimeter Do not carry out the measurement when the Meter's back case and battery compartment are not closed to a
MT-3109 AC/DC Digital Clamp Multimeter International Electrical Symbols AC (Alternating Current) DC (Direct Current) AC or DC Grounding Double In
MT-3109 AC/DC Digital Clamp Multimeter Rotary Switch Below table indicated for information of rotary switch positions. Rotary Switch Position Function
MT-3109 AC/DC Digital Clamp Multimeter Button Operation Performed Select Press SELECT button to select the alternate functions marked in blue col
MT-3109 AC/DC Digital Clamp Multimeter No. Symbol Meaning 1 AC Indicator for AC voltage or current 2 DC Indicator for DC voltage 3 The battery is
MT-3109 AC/DC Digital Clamp Multimeter Measurement Operation A. DC/AC Voltage Measurement (see figure 3) Warning To avoid harms to you or damages
Kommentare zu diesen Handbüchern